At a pile foundation construction site in Jieyang, Guangdong, underground soft soil layers, sand layers, and hard rock interlayers alternate in an orderly manner, with frequent soft and hard mutations. The rotary excavation construction is in trouble: the angle of the barrel drill row gauge is deviated, resulting in abnormal loss of picks, frequent chipping and broken teeth, a sudden drop in drilling efficiency, and high costs. This article combines front-line cases to dismantle the root causes and provide optimization plans to help construction parties reduce losses and improve efficiency.

1. Construction site pain points: Under complex strata, the difficulties in barrel drilling construction are highlighted.
The stratum of the construction site has “soft-hard-soft” disordered interlayers and strong lithological heterogeneity. The core problems are concentrated in: a single pile needs to replace 3-5 picks, and the loss is 2-3 times higher than that of conventional strata; the footage speed is only 50% of the normal stratum, and the construction period lags; the cost of a single pile rises by more than 30%; uneven stress on the drilling tool can easily cause deviation holes and collapse holes, affecting the quality of the pile. The investigation found that the core problem was that the angle of the barrel drill gauge did not match the complex formation. Even a 5° deviation would accelerate pick loss.
2. Dismantling the root cause: the loss logic of the unbalanced ruler angle
The cutting angle and side slip angle of the barrel drill ruler directly determine the stress and life of the pick. Complex formations will amplify the hazards of angle imbalance:
- Cutting angle deviation: The original uniform setting is 50°, which is neither suitable for soft soil layers (adapted to 32°-35°) nor hard rock layers (adapted to 40°-45°), resulting in eccentric wear of soft rock and tooth chipping of hard rock.
- Side slip angle imbalance: The original angle is 15° and there is no differentiated design, which exceeds the reasonable range (5°-15°), resulting in unilateral wear and fatigue fracture of the pick. The wear of the external teeth is twice that of the internal teeth.
- The hazards amplified by formation characteristics: alternating soft and hard conditions bring about alternating stress impacts and drill tool deflection vibrations, further aggravating pick wear and chipping.

3. Breakthrough plan: Optimization measures for barrel drilling adapted to complex formations
Combined with the actual conditions of the construction site, optimization was carried out from the four major dimensions of angle customization, tooth layout optimization, parameter adjustment, and pick selection. The results have been verified by test drilling to achieve remarkable results:
- Differentiated ruler angles: external teeth (cutting angle 42°-45°, side slip angle 8°-10°) are suitable for hard rock; middle teeth (40°-42°, 6°-8°) balance force; internal teeth (35°-38°, 5°-6°) are suitable for soft layers and assist in slag removal.
- Optimize the tooth layout design: the tooth spacing is controlled to 22-25cm, and the soft and hard junction sections are encrypted by 15%-20%; an asymmetrical arrangement is used to disperse the impact load; the tooth tip height difference is 3mm to achieve step cutting.
- Supporting construction parameters: low drilling pressure (5-8MPa), medium rotational speed (60-80r/min) for soft soil layers; low rotational speed (30-50r/min), appropriate lifting drilling pressure for hard interlayers; use of strong guide barrel drills, and pretreatment of the soft and hard interface sections.
- Selection of suitable picks: Choose impact-resistant picks with thick handles to enhance wear resistance and impact resistance and reduce losses from the source.

4. Optimization effect: actual measured data confirms the effect
After the implementation of the plan, the on-site measured data improved significantly: the pick loss rate was reduced by 42%, and the replacement quantity of a single pile was reduced to 1-2; the drilling efficiency was increased by 38%, 2-3 piles were built in a single day, and the construction period was shortened by 25%; tooth chipping accidents were reduced by 70%, and the comprehensive cost of a single pile was reduced by 28%, which was recognized by the construction party.
5. Summary
In rotary excavation construction in complex strata, the angle of the barrel drill row is the key to affecting the life, efficiency and cost of the pick. Blindly following common solutions will only lead to a vicious cycle. Customized optimization can reduce losses and improve efficiency. If you face similar problems, you can communicate with Mailinmat to customize exclusive solutions.