There is a common problem in mining and tunnel construction sites: the appearance of the cutting picks is intact and the alloy heads are not damaged, but they frequently loosen, fall off, and wear eccentrically, resulting in repeated shutdowns for parts replacement, which not only increases the cost of consumables but also delays the construction period. Most people’s first reaction is that the quality of the pick is not good. In fact, the root cause of most abnormal tooth damage is the circlip. This small part is precisely the key to fixing the pick and ensuring the stability of excavation.
This article breaks down: how the circlip affects the life of the pick, common failure modes, key points for avoiding pits, and standardized usage methods.

01 The core function of the circlip: the fixed “safety lock” of the pick
The pick breaks the rock and the circlip locks it. Only by matching the two can the operation be stable. Under the impact of high-frequency vibration, the circlip has two key functions: one is to limit and prevent disengagement-accurately engage the slot to prevent shaking, deflection, and falling off; the other is to buffer and protect the piece-elastically absorbs impact, reduces hard wear, and extends the life of the entire piece.
In short: No matter how good the pick is, if the circlip is of poor quality, mismatched or improperly installed, it will be scrapped early and malfunctions will occur frequently.

02 Three major construction site failures caused by improper circlips
There are two common bad habits at construction sites – changing only the picks without replacing the circlips, and using mixed-brand circlips. This is the hidden culprit of high consumable costs. There are three specific hazards:
Unexpected tooth loss: The old circlip has elastic fatigue, tension attenuation or inconsistent specifications, and gradually loosens during vibration. The intact tooth picks directly fall off and are lost, especially under hard rock conditions.
Scrap due to eccentric wear: The circlip is not firmly fixed, the pick shakes at an angle, and cannot bear force vertically, resulting in unilateral eccentric wear, cracking of the alloy head, and a large number of picks being scrapped in advance.
Damage to the tooth holder, a vicious cycle: inferior circlips are easy to break, and the fragments scratch the tooth holder slot, causing permanent damage. Subsequent replacement of new picks will also be difficult to securely fix.

03 Quickly avoid pitfalls: 4 most common misunderstandings
In actual working conditions, we often find a misunderstanding: most equipment failures are not due to product quality, but hidden dangers buried by irregular construction habits!
The elasticity of old parts will be reduced due to repeated use. The circlip is a wearable part, and its elasticity will be seriously attenuated after repeated disassembly and assembly. Repeated use in order to save trouble will cause the tightening force to drop significantly, which can easily lead to loosening and failure.
Mixing models randomly reduces compatibility; the slot sizes for roadheading teeth, coal mining teeth, and rotary excavation teeth are all different, so retaining rings must be used according to their specific type. Using different models interchangeably not only reduces compatibility but also leads to instability.
Choosing cheap, low-quality products can’t handle high intensity; inferior retaining rings often lack proper heat treatment, making them either too brittle and easy to break or too soft and prone to deformation, unable to withstand high-intensity excavation, which is a false economy.
Being careless during installation, details determine success or failure; if iron filings or debris remain in the slot, or if the retaining ring is not fully seated or misaligned, it can create major risks of loosening later.
💡Friendly tip: Follow proper procedures and pay attention to the details! Avoid violations to ensure efficient equipment operation.
04 Minimal Standard Installation Steps

Following standard installation can greatly reduce tooth loss and wear failures:
Clean: Remove mud and metal shavings from the tooth seat and slot to ensure the contact surface is smooth and clean.
Pairing: Choose a brand new dedicated circlip according to the tooth type, avoiding mixing old and new parts or mismatched specifications.
Installation: Lightly lubricate to assist, fully slot the circlip into place without shifting or lifting.
Recheck: Gently shake the tooth, if there is no wobble or movement, confirm it is secure before use.
05 Construction Site Cost-Saving Summary
When cutting costs on a construction site, don’t just focus on the price of the teeth; the retaining spring is the low-cost, high-return control detail. Sticking to ‘always replace the spring when changing teeth, ensure compatibility when selecting, and install properly’ can effectively reduce waste of materials and downtime, easily achieving quality improvement and cost reduction.