The junction zone of red and white sandstone, the area hardest hit by pick loss? This is the most effective way to crack

The junction zone of red and white sandstone can be called the “pick nemesis” of tunnel and mine excavation. The pick loss rate directly affects the efficiency and cost of excavation. Why is sandstone, which seems so easy to dig, more difficult to dig than hard rock? How to break through when encountering such formations? Merinmate combines geological origin and wear core to provide a complete set of solutions to help you reduce tooth wear, improve footage, and save costs from the root cause.

red and white sandstone

1. Why is the junction of red and white sandstone the “hardest hit area” for excavation cutting tools?

The junction zone of red and white sandstone is a composite formation with interlayered soft and hard layers, sudden changes in composition, and extremely abrasive properties. Its three “fatal characteristics” have become obstacles to tunneling:

  •  Quartz “whetstone” effect

The quartz content of white sand often exceeds 60%, and its texture is hard and highly abrasive. During excavation, the pick rotates at high speed with the cutterhead, and the moving quartz particles continue to scrape the pick alloy head and tooth body, causing abrasive wear – the pick does not “crash” the rock, but is “slowly worn” by the rock particles. Ordinary pick alloy heads will be quickly passivated and worn, and cannot effectively break rocks. Frequent shutdowns are required to change teeth, which seriously slows down the progress.

  • Soft and hard alternating impact

Red sandstone (soft) and white sandstone (hard) are alternately distributed. Each time the pick rotates with the cutterhead, it will undergo drastic force changes of “soft cutting → hard impact → soft cutting”. Ordinary picks are not only difficult to withstand alternating stress, but are prone to cracks at the welding joint, causing the alloy head to fall off, chipping, and even tooth body fractures; they can also cause deflection due to uneven stress on the cutterhead, exacerbating unilateral wear of the pick, and causing damage to the cutterhead.

  • Rock powder “sandblasting effect”

During excavation, the crushing of red and white sandstone will produce a large amount of quartz fine rock powder, which will form a high-pressure sandblasting erosion effect with the high-speed rotation of the cutterhead, causing double damage to the pick: the strength of the tooth body and tooth seat will decrease after being washed away at high speed, and the tooth body will be ground to form a “thin neck”. When cutting from red sandstone to white sandstone, the impact load will double, which can easily lead to tooth body fracture, resulting in the waste phenomenon of “intact alloy, tooth body fracture”, and increase the cost of consumables.

2. The key to breaking the game: choosing the right pick + optimizing the ruler + adjusting parameters

When digging in the junction zone of red and white sandstone, “hard work” will only increase losses, and precise response is the way to go.

Special pick

(1)Use special picks

Ordinary picks will fail in this formation, so special reinforced models with “high wear resistance + impact resistance + anti-erosion” must be selected. The core configuration is as follows:

  • Alloy head: ultra-coarse grain + high tungsten formula, anti-wear and anti-collapse

Ultra-coarse-grained cemented carbide (WC grain size ≥ 6 μm) or multi-component alloy is selected, with a hardness HRA ≥ 92. The wear resistance is increased by 2 times and the impact resistance is increased by 30%. It is suitable for alternating soft and hard working conditions. It adopts a large alloy head design to increase the wear-resistant volume and extend the tooth replacement cycle.

  • Tooth body: high-strength steel + wear-resistant surfacing, anti-wear and anti-breakage

The tooth body is made of 42CrMo alloy structural steel, which has been quenched and tempered + deep quenching. The toughness of the handle is HRC35-38 and the wear-resistant layer of the head is HRC48-52, achieving “tough inside and hard on the outside”; alloy beans or ceramic coatings can be added to enhance surface wear resistance and avoid grinding and fracture of the tooth body.

  • Process: Vacuum cutting and welding + spin optimization, preventing stripping and eccentric wear

Vacuum cutting and welding can avoid welding defects, make the joint strength of the alloy head and tooth body ≥500MPa, reduce the risk of desoldering by more than 60%, and adapt to alternating impact; optimize the matching accuracy of the tooth handle and the tooth seat, add a spin groove, ensure that the pick can rotate freely, receive uniform force, and reduce unilateral eccentric wear.

(2) Optimize layout

Mailinmat underground real shot

Conventional equal-spaced arrangement can easily cause multiple picks to cut into white sandstone at the same time, causing a sudden increase in load and aggravating impact wear. The arrangement strategy needs to be optimized:

  • The asymmetrical arrangement with variable spacing ensures that only 1-2 picks act on the interface at any time to disperse the impact load;
  • Increase the inclination angle of the side teeth from 45° to 50°–55° to strengthen pre-crushing and release stress on the main teeth;
  • It is known that the construction section of the junction zone is temporarily enlarged by 15%–20% of the picks to reduce the single tooth load.

(3) Adjust excavation parameters + key construction methods

Follow the principle of “three reductions and one increase” (load reduction, deceleration, footage reduction, and frequent inspections), and combine key construction methods to reduce pick loss.

Parameter adjustment: The cutterhead pressure is reduced to 60%-70% of the normal value to avoid pick overload; the rotational speed is adjusted to 10-15r/min to reduce the friction frequency; the single footage is reduced to 30-50cm to avoid “hard chewing” of the cutterhead; the machine is stopped for inspection every 1m of excavation, and a comprehensive inspection is performed every 50m. If the wear exceeds 50%, chipping or cracks are replaced immediately (parameters can be fine-tuned based on on-site geology).

Key construction methods: When excavation reaches 1-2m above the junction zone, put 20-50mm graded gravel for compaction to reduce the eccentric wear rate of the picks by more than 60%; reverse the cutterhead once every 5m of excavation to avoid excessive wear on one side; spray the cutterhead at full speed to cool the picks and wash away rock powder; clean the gear seat and apply high-temperature grease every shift to ensure the flexibility of the picks.

Mailinmat products

3. Summary

Facing the junction zone of red and white sandstone, which is a “heavy tooth-disaster area”, we should not act haphazardly, but should do scientific and standardized operations. Only through professional pick selection, reasonable sizing strategies and scientific excavation methods can it be transformed into an “efficient excavation area” and truly reduce consumption and increase efficiency.