This guide to coal mining excavation: Why is it recommended that you switch to graded carbide picks?

Anyone who engages in coal mining knows that ordinary picks have long faced an endless cycle of performance – those that are wear-resistant are not resistant to smashing, and those that are resistant to smashing are not wear-resistant.

Homogeneous carbide cutting picks are prone to chipping and alloy loss when encountering gangue or hard rock; after the toughness is increased, the tooth tips quickly become blunt, resulting in frequent shutdowns for coal mining and excavation to replace the teeth, and the cost of consumables and lost work remain high.

Gradient carbide picks break the dilemma in terms of material structure and are specially adapted to complex underground working conditions of coal mining and excavation, allowing the picks to withstand both impacts and continuous wear.

1. Why do ordinary picks become more and more ineffective the more they are used?

In underground operations, picks face three major losses for a long time:

1. Abrasive wear: Coal rock and quartz sandstone continue to rub, the tooth tips quickly become passivated, the mining resistance increases, and the equipment consumes oil;

2. Impact cracking: When encountering hard gangue or faulted hard rock, the homogeneous alloy has insufficient impact resistance and is easily prone to tooth chipping and head loss;

3. Thermal fatigue cracking: high-speed friction and high temperature + spray cooling, repeated alternation of cold and heat, micro-cracks will occur in the alloy, and it will gradually fragment and be scrapped.

Homogeneous alloys with a single formula can only choose one of two options: either they are wear-resistant and brittle, or they have poor wear-resistance, making it difficult to fully adapt to complex geological conditions.

2. Core advantages of gradient alloy: layered adaptation, two-way consideration

Our gradient cemented carbide adopts a gradient structure from the surface layer to the core, with a smooth transition of cobalt content and grain size, without stress faults, and each layer performs its own duties:

✅ Surface high-hard wear-resistant layer: low-cobalt ultra-fine grains, high hardness, strong resistance to sand and stone abrasion, long-term self-sharpening, and delaying tooth tip passivation;

✅Middle layer buffer transition layer: gently connects the internal and external structures, disperses impact stress, and prevents cracks from spreading;

✅ Core high-toughness impact-resistant layer: high cobalt and high toughness, strong absorption of hard rock impact energy, effective prevention of tooth chipping, U-turn and fracture.

To put it simply: the surface layer specializes in wear resistance and saves consumables, and the core layer specializes in smash resistance and reduces scrap.

3. Two core underground scenarios, actual measurement of cost reduction and efficiency improvement

1. Coal shearer fully mechanized mining working face (coal seams with gangue, deep mines)

In view of the working conditions of coal seams containing gangue and high ground stress, gradient picks can effectively solve the problems of ordinary picks grinding quickly and collapsing due to collision with gangue. Comparison of actual measurements: Under the same mining conditions, the service life of gradient picks is increased by more than 2 times, the tooth consumption of 10,000 tons of coal is significantly reduced, and frequent shutdowns for tooth replacement are reduced.

2. Tunnel boring machine rock tunnel construction (semi-coal rock tunnel, full rock hard tunnel)

Hard rock and high quartz rock formations are the areas hardest hit by pick loss. With its high wear-resistant surface layer and strong core, the gradient alloy can increase the tunneling depth by 2-3 times, significantly reducing the probability of eccentric wear and chipping, reducing the no-load load of the equipment, reducing fuel consumption and accessories loss, and ensuring continuous tunnel excavation construction.

4. Visible comprehensive income from mining areas

1. Reduced consumables: the service life is far longer than that of ordinary homogeneous picks, greatly reducing the frequency of purchases;

2. Improve efficiency: reduce downtime and gear replacement time, and continue to stabilize mining progress;

3. Save labor: reduce the intensity of underground gear changing operations and reduce construction safety hazards;

4. Protect equipment: The tooth shape is sharp and stable, and the force is evenly distributed to reduce abnormal wear of the gear seat, gun head, and roller.

5. Source manufacturer’s process guarantee

As a professional cutting pick manufacturer, we strictly control the core process of gradient alloy: integrated gradient sintering, no layering gaps, stable metallographic structure, and fully automatic vacuum brazing, the alloy head and tooth body have high bonding strength. All models are fully covered, and the gradient alloy proportioning plan can be customized according to the geology of the mining area.

Conclusion

The key to reducing mining costs is to upgrade wearing parts. Gradient carbide picks effectively break through the industry shortcomings of “wear-resistant but not impact-resistant, impact-resistant but not wear-resistant”, adapt to most complex underground working conditions, use less consumables and less downtime, and achieve efficient and stable production in mining areas.

There are high-loss working conditions such as gangue and hard rock. You can send a private message for free consultation on model selection and apply for working condition comparison samples! Contact us