If the rotary drilling rig picks are consumed too quickly, it will seriously affect the construction efficiency and increase the cost. Most people mistakenly think it is a pick quality problem, but in fact it is caused by the superposition of factors such as working condition adaptation, operating specifications, and equipment status. Master the 3-step self-diagnosis method to quickly locate the root cause and reduce consumption without the need for a professional team.
Let’s first clarify: How to distinguish between normal consumption and abnormal consumption?
First, distinguish between normal and abnormal consumption: the pick can be used for 80-120 hours in soft soil, 40-80 hours in medium-hard rock, and 20-40 hours in hard rock.
If the service life of the pick is much lower than the corresponding standard, or there is short-term grinding, chipping, or broken handles, and if batch quality problems are excluded, it is abnormal consumption. Follow the following steps to diagnose.

3-step core diagnosis method: from easy to difficult, quickly locate the problem
The diagnosis follows the logic of “look at the pick first → then check the operating equipment → finally combine the working conditions”, and can be completed on site without the need for complicated tools.
Step 1: Observe the wear pattern of picks and initially determine the type of problem
The shape of pick wear is an intuitive signal. There are 4 common situations corresponding to different reasons:
- Uniform grinding: only the service life is not up to standard, mostly due to poor material workmanship or inconsistency between model selection and working conditions;
- Unilateral eccentric wear: uneven force due to installation angle deviation, gear seat deformation or non-vertical drill pipe;
- Broken edge/broken handle: common in hard rock and pebble-containing strata due to insufficient toughness of the pick or forced drilling;
- Tooth head falling off: caused by poor welding process or frequent severe impact.
Tips: Compare the old and new picks to accurately determine the type of wear.

Step 2: Check operation and equipment status to avoid human and equipment hazards
Improper operation or abnormal equipment are common causes. Focus on three points:
- Operating specifications: Avoid forced drilling and overload operations, and control the drilling speed;
- Equipment calibration: Check the verticality of the drill pipe, the status of the gear seat and the installation torque of the pick to prevent rotation failure;
3. Lubrication and cooling: Lubricate the gear seat regularly and turn on the cooling system for hard rock operations to avoid high temperature wear.

Step 3: Review the working conditions to confirm the adaptability issues
The mismatch between model selection and working conditions is the core root cause. Combined with the formation review, there are two points:
- Stratum adaptation: For soft soil layers, choose the sharp-edged model, for hard rock, choose the high-hardness and high-toughness model, and for pebble-containing strata, choose the impact-resistant model;
2. Pick parameters: For hard rock working conditions, picks with HRC65 or above and impact energy ≥120J/cm² should be selected, and the cutting edge angle should be suitable for the formation.

Solutions to common problems (for reference)
Quick solutions to abnormal problems:
- The material/workmanship is not up to standard: replace the pick with suitable working conditions and high-quality workmanship;
- Installation/equipment deviation: calibrate the drill pipe, clean and replace the gear seat, and install the pick according to standards;
- Improper operation: standardize the operation, break the hard rock in advance, and ensure lubrication and cooling;
4.Mismatch in selection: Replace the corresponding type of pick according to the stratum.
Professional tip: Precise adaptation is the key to reducing consumption
Excessive consumption of picks is caused by a comprehensive imbalance of multiple factors. Finding the “mismatch” links and targeted optimization can reduce consumption and improve efficiency.
We are deeply involved in the research and development of rotary digging picks and their adaptation to working conditions. Most abnormal pick consumption is caused by improper selection or operation. Precise adjustment can increase the service life by more than 50%.

Conclusion: Independent diagnosis, efficient cost reduction, and easy response to the problem of pick consumption
Mastering the 3-step diagnostic method can quickly find the root cause and optimize on-site to maximize the value of each pick.
If self-diagnosis fails or you don’t know how to choose, you can contact us for free working condition investigation and one-on-one guidance.