High Specific Pressure, Low Haulage Speed! Technical Experts Reveal: How to Prevent Mass Pick Cutter Chipping at the Source in Hard‑Rock Tunnelling

Today, starting from the real‑world pain points of hard‑rock construction, we will discuss how to stop mass pick cutter chipping at the source by adjusting the feed rate in advance, so that every pick cutter can deliver its full value.

▼
❶ Where Does Mass Cutter Chipping Occur?

In hard‑rock construction, pick cutters bear frequent alternating impact loads. When the roadheader encounters a sudden rise in rock hardness, problems will arise if operators fail to adjust cutting parameters promptly.

Excessive haulage speed and over‑deep cutting depth are the primary culprits for instantaneous overload on pick cutters.

Under such working conditions, the impact force imposed on the carbide tip exceeds the design threshold. Minor damage leads to carbide spalling, while severe cases result in shank fracture. Once mass chipping takes place, the force balance of the entire row of cutters is disrupted, tunnelling efficiency plummets, and replacement costs multiply dramatically.

❷ Why Can Pre‑Adjusting the Feed Rate Solve the Root Problem?

Many construction workers hold a misunderstanding: hard‑rock tunnelling means pushing equipment to full power to force through rock. In fact, the professional method runs in the opposite direction. Hard‑rock construction follows the principle of high specific pressure, low haulage speed.

“High specific pressure” means increasing the pressure of the propel cylinder to raise the penetration pressure of a single cutter into rock, enabling the pick cutter to cut into the rock rather than simply scrape its surface. “Low haulage speed” refers to moderately reducing the slewing or propel speed, ensuring each pick cutter has enough time to break rock effectively.

The core logic of pre‑adjusting the feed rate is to actively lower the haulage speed and cutting depth before entering hard‑rock sections, switching the working mode of pick cutters from brute‑force operation to stable and steady cutting. This measure brings three major benefits: • Prevent instantaneous overload: A reduced feed rate lowers the single‑pass cutting volume of each pick cutter for more uniform stress, eliminating chipping caused by stress concentration from the source. • Improve rock‑breaking efficiency: Although the working pace seems slower, every cut achieves effective rock fragmentation and avoids invalid wear from idling scraping. • Extend overall service life: Pick cutters operate within the rated load range with a gentle wear curve. The service life of the whole batch stays consistent, preventing the chain reaction of “one broken cutter triggering damage across the entire row”.

❸ On‑Site Parameter Adjustment: Lessons from Front‑line Practice

At the No.1 Fully Mechanized Excavation District of a coal mine in Shandong, crews faced large‑section hard rock. After repeated on‑site tests and dynamic optimisation of cutting parameters, they adopted a “small‑step advance” strategy: reducing cutting depth while increasing cutting cycles. This approach effectively cut down roadheader impact and drastically reduced pick cutter consumption.

A coal mine in Shaanxi provides another valuable reference. Faced with rock with a high Protodyakonov coefficient and excessive cutter loss, the mine abandoned the crude “force‑against‑force” working mode. Adjusting for varying rock hardness, the traditional one‑pass forming cutting was optimised into a “bottom‑up, layered stripping construction method”: a bottom slot is cut first to create a free face, followed by layered reaming and profiling, which greatly reduces invalid wear on pick cutters.

These field practices prove that pre‑adjustment is not a slowdown, but stability; not a retreat, but progress.

❹ Indispensable Supporting Measures

Naturally, adjusting the feed rate alone is not enough. The following supporting actions are equally critical:

  1. Precision Cutter Selection Matched with Working Conditions For hard rock or highly abrasive formations such as sandstone, select pick cutters made of high‑wear‑resistant cemented carbide. Avoid blind pursuit of extreme hardness, which may lead to carbide chipping and shank breakage. Obtuse‑angle cutters (90°‑110°) are better suited for hard‑rock conditions and extend wear resistance effectively.
  2. Build Consumption Logs for Full‑Life‑Cycle Management Record the wear condition of pick cutters for every shift. Replace cutters in a timely manner once wear or carbide detachment is detected. Shifting from breakdown maintenance to preventive maintenance can greatly reduce equipment failure rates.
  3. Standardise Operations and Reckless Working Practices Blind cutting and forced rock excavation by operators will accelerate pick cutter wear. Deliver regular operational training, standardise workflows and lower human‑induced losses through standardised construction.

❺ Optimal Construction Solution: Premium Pick Cutters plus Scientific Working Methods

Pre‑optimising the feed rate is not an optional choice but a necessary measure. As a pick cutter manufacturer, we not only supply high‑quality products but also provide customers with professional cutting‑parameter suggestions and dedicated technical support.

With well‑selected cutters and optimised parameters, hard‑rock tunnelling can be carried out smoothly and efficiently. If you are troubled by high pick‑cutter consumption in your hard‑rock tunnelling projects, please feel free to get in touch with us — let every pick cutter deliver its maximum potential value!