In view of the common failure problems such as wear, fracture, bit falling off and corrosion of coal mining picks in use, corresponding selection standards and protection measures for coal mining picks are formulated according to the physical characteristics (hardness, gangue content, humidity, etc.) of different coal and rock types, which can effectively extend the service life of coal mining picks and improve the cutting efficiency. The specific points are as follows:
I. Soft Coal Seam (Hardness f≤3, no gangue or a small amount of soft gangue)
(I) Selection Points
- Bit Material: Select cemented carbide bits with moderate toughness and acceptable wear resistance (such as YG11C). There is no need to excessively pursue high hardness to avoid chipping caused by excessive brittleness of the material; the bit shape is preferably pick-shaped with a sharp cutting edge, which can reduce the risk of adhesive wear.
- Tooth Body Material: Adopt 42CrMo alloy steel, which is quenched and tempered to ensure sufficient toughness and prevent fatigue fracture caused by load fluctuation during cutting; the surface of the tooth body can be galvanized or chrome-plated for rust prevention to cope with the humid underground environment.
- Structural Selection: Select picks with short tooth body and large cutting angle to reduce the contact area between the tooth body and coal, lower adhesive wear and cutting resistance, and improve cutting fluency.
(II) Protection Points
- Control the cutting speed to avoid coal debris adhering to the bit surface due to excessive speed, forming adhesive wear pits; regularly clean the adhering substances on the bit, and high-pressure water flushing can be used to assist slag removal.
- Ensure accurate pick angle during installation (cutting angle controlled at 30°-45°) and tight fastening bolts to prevent increased local wear of the tooth body caused by uneven force.
- Regularly check the integrity of the anti-rust layer on the tooth body. If damage is found, timely touch up with anti-rust agent to avoid corrosion caused by the humid environment.

II. Medium-Hard Coal Seam (Hardness 3<f≤6, a small amount of hard gangue, gangue hardness f≤8)
(I) Selection Points
- Bit Material: Select high-hardness and high-wear-resistance cemented carbide bits (such as YG15, YG16). The edge of the bit is strengthened to improve the resistance to impact wear and abrasive wear, so as to cope with the impact load during gangue cutting.
- Tooth Body Material: Adopt high-strength alloy steel, which is subjected to “quenching + tempering” composite heat treatment to balance hardness and toughness (hardness HRC45-50), reduce the risk of fatigue fracture and brittle fracture; the root of the tooth body is rounded to reduce stress concentration.
- Structural Selection: Select pick-shaped or knife-shaped picks with moderate tooth body length. The brazing between the bit and the tooth body adopts vacuum brazing technology to improve the bonding strength of the brazing layer and prevent the bit from falling off; in some scenarios, picks with wear-resistant alloy strips can be selected to enhance the side wear resistance.
(II) Protection Points
- Optimize the cutting path to avoid large gangue as much as possible. If it is unavoidable, reduce the cutting speed to reduce the damage of impact load to the bit and tooth body.
- Regularly check the integrity of the brazing layer. If cracks or oxidation of the brazing layer are found, replace the pick in time to avoid the bit falling off; at the same time, check the wear of the tooth holder. If the tooth holder is deformed, repair or replace it in time to prevent changing the cutting attitude of the pick.
- Adopt the “regular rotation” strategy to exchange picks at positions with large force with those at positions with small force, balance wear and extend the overall service life.

III. Hard Coal Seam (Hardness f>6, more gangue and hard rock interlayers, gangue hardness f>8)
(I) Selection Points
- Bit Material: Select super-hard cemented carbide bits (such as YG20, YT15) or composite coated bits (such as TiN, TiC coating) to significantly improve hardness, wear resistance and impact resistance, so as to cope with severe abrasive wear and impact during hard rock cutting.
- Tooth Body Material: Adopt high-strength wear-resistant alloy steel, add alloy elements such as chromium, molybdenum and vanadium, and undergo deep quenching and low-temperature tempering treatment to improve the overall strength and toughness of the tooth body and prevent impact fracture; the surface of the tooth body is subjected to wear-resistant surfacing treatment to enhance wear resistance.
- Structural Selection: Prefer knife-shaped picks with wide and firm cutting edges, which can disperse cutting load; the pick head is designed to be streamlined to reduce cutting resistance; the brazing process adopts high-frequency induction brazing to ensure dense brazing layer and high bonding strength, combined with post-welding heat preservation treatment to eliminate internal stress.
(II) Protection Points
- Equip with cutting load monitoring device to real-time monitor load changes and avoid overload cutting; if necessary, adopt pre-splitting blasting technology to treat hard rock interlayers and reduce the impact load on picks.
- Shorten the pick inspection cycle. After each cutting operation, check the bit wear, chipping and tooth body cracks. If problems are found, replace them immediately to prevent broken picks from damaging the tooth holder and fully mechanized mining equipment.
- Optimize the lubrication scheme. Apply high-temperature wear-resistant grease at the contact between the pick and the tooth holder to reduce friction and wear; at the same time, strengthen underground ventilation and dehumidification to reduce environmental humidity and assist in reducing corrosion.

IV. Corrosive Mine Environment (High Humidity, Acid Mine Water, Saline Content)
(I) Selection Points
- Tooth Body Protection: Select stainless steel tooth body or perform multi-layer anti-corrosion treatment on the surface of ordinary tooth body (such as fluorocarbon coating, ceramic coating) to improve the resistance to electrochemical corrosion and chemical corrosion; avoid using ordinary carbon steel tooth body to prevent rapid rusting.
- Bit and Brazing Layer: Select cemented carbide bits with good corrosion resistance, use corrosion-resistant brazing materials for the brazing layer, and perform anti-corrosion sealing treatment after brazing to prevent mine water from seeping into the gaps of the brazing layer and aggravating corrosion and crack propagation.
(II) Protection Points
- After the operation, timely clean the mine water and coal rock debris on the surface of the pick, wipe it dry and apply anti-corrosion grease to isolate corrosive media.
- Regularly check the integrity of the pick anti-corrosion layer. If damage or falling off is found, timely touch up with anti-corrosion materials or replace the pick; at the same time, optimize the mine water treatment process to reduce the acidity and salt content of mine water and reduce corrosion from the source.
