Tackling tight hard rock: assisted drilling to reduce strength, efficient pick locking

In underground engineering, hard rock has always been a “stumbling block” in front of the construction team. Especially when encountering dense hard rock with a uniaxial compressive strength of over 180MPa, the tunnel boring machine is like chewing on a “whetstone”. Not only does it advance slowly and equipment losses increase sharply, but frequent tool changes will also make the construction period passive and construction costs skyrocket.

Assisted drilling: breaking the strength barrier of hard rock

The “stubbornness” of hard rock comes from its high strength and high integrity. Traditional mechanical hard punching and hard cutting not only consumes huge amounts of energy, but can also easily cause pick breakage and cutterhead vibration, falling into a cycle of “harder, slower, slower, more energy consumption”. The auxiliary drilling technology uses “softness to overcome hardness” to break the situation. It constructs a pressure relief zone through advanced drilling, causing micro-cracks and stress redistribution inside the hard rock to achieve strength weakening. Whether it is ultrasonic vibration collaborative operation or high-pressure jet pre-fracturing, the core is to weaken the rock mass structure in advance. Research shows that after treatment, the cutting resistance of hard rock can be reduced by 15%-20%. While the excavation speed is increased, equipment damage and tool wear can also be effectively controlled. “Weakening first, then cutting” has become the mainstream mode for efficient construction of hard rock.

Core empowerment: locking in efficient cutting results

However, it is worth noting that auxiliary drilling only completes the first step of “strength reduction”. The final achievement of excavation efficiency still relies on the “last mile” core component of the pick. Although the weakened rock reduces the difficulty of cutting, it still has extremely high requirements for the wear resistance and impact resistance of the pick. If the quality of the pick is not up to par, even if the strength of the rock decreases, problems such as excessive wear and loss of the cutter head will still occur, greatly reducing the advantages of auxiliary drilling. At this time, a high-quality pick adapted to hard rock working conditions becomes the key to improving construction efficiency. Merinmate cutting tools are exactly the “tough weapon” created to solve the difficult problems of hard rock excavation. From material selection to process polishing, from rigorous inspection to actual combat verification, each pick has been tempered and perfectly adapted to the hard rock cutting needs after auxiliary drilling and strength reduction, allowing efficient excavation throughout the entire construction process.

Hard-core quality: excellent materials and craftsmanship

  • Preferred material: both strength and toughness online

The 35CrMnSi alloy steel with excellent hardenability is selected and professionally heat treated to achieve a golden balance of strength, hardness and toughness, which can withstand the severe impact and alternating load of hard rock cutting. The cutter head is made of high-purity straight cylindrical tungsten-cobalt alloy, with optimized tooth tip and cutting edge design, which has strong fit and low loss, and avoids the hidden dangers of tooth chipping and shank breakage from the source.

  • Exquisite craftsmanship: Keep the bottom line of quality in every detail

Exquisite craftsmanship is the key to adapting the pick to hard rock working conditions. The core welding adopts vacuum brazing technology to achieve a metallurgical solid connection between the tooth body and the cutter head, eliminating problems such as false welding and cracks, and the cutter head shedding rate is almost zero; after welding, vacuum heat treatment is performed to optimize the grain, reduce stress, and superimpose a special wear-resistant coating to effectively resist wear and corrosion and greatly extend the service life under hard rock conditions.

  • Strict standard control: ensuring uniform quality throughout the entire process

Mailinmat adheres to the standard of “consistent quality” and establishes a strict inspection system for the entire process. From raw materials to finished products, the entire process is strictly controlled, and the inspection standards are unified without compromise. Actual combat data shows that it can nearly double the excavation efficiency, reduce the comprehensive construction cost by 18%-25%, and maintain the bottom line of construction schedule and cost.

Choosing Mailinmat means choosing stability and peace of mind.

The efficient breakthrough in hard rock excavation lies in the coordinated effort of “construction strategy + core equipment”. Auxiliary drilling paves the way for hard rock strength reduction, and Melinmat picks escort efficient cutting. The two complement each other to solve construction problems. Regardless of complex working conditions such as tunnels and mines, choosing Malinmate picks means choosing stability and efficiency, and empowering hard rock projects with hard-core quality.