In 120MPa hard rock excavation, traditional cutting picks often fall into a dilemma: if the alloy is too hard, the tooth body will be scrapped first; if the tooth body is wear-resistant, the alloy will collapse prematurely. In addition, high temperature and alternating loads induce clusters of micro-cracks, making the picks blunt with use, and the excavation efficiency continues to decline.
In response to the pain points of hard rock excavation, we take “synchronous consumption of alloys and teeth” as the design core and integrate the “bionic self-sharpening” function to reduce the frequency of tooth replacement, shorten downtime, increase the excavation speed, and provide a reliable hard-core solution for ultra-hard rock conditions.

1. 120MPa hard rock: the “ultimate testing ground” for picks
120MPa hard rock (such as slightly weathered granite, dense limestone) is extremely abrasive, and the pick mainly faces three losses:
- Impact cracking: Under strong impact load, the alloy is easy to chip and the tooth body is easy to break. Traditional picks need to be replaced frequently every shift.
- Asynchronous wear: The hardness of the alloy and the tooth body does not match, the material utilization rate is less than 40%, and there is often a waste situation of “the alloy is intact and the tooth body has been polished”.
- High-temperature deterioration: The cutting friction temperature exceeds a certain temperature, causing thermal fatigue micro-cracks, material softening, and excavation efficiency continues to decline.
2. Core breakthrough: simultaneous consumption + self-sharpening and crack suppression to eliminate ineffective losses
Through gradient material matching and structural optimization, we have achieved precise synchronization of the pick wear rate, so that it can always remain sharp during operation and fully utilize the value of every piece of material.

- Gradient material matching
- Alloy head: Made of low-cobalt, extra-coarse-grained super wear-resistant carbide, which has both extremely high wear resistance and crack resistance.
- Tooth body: Made of 35CrMnSi alloy steel, it has been cold forged and multi-stage heat treated to form the characteristics of “tough inside and stiff outside”, which can effectively buffer impact loads.
- Brazing layer: The vacuum furnace brazing process is used to increase the bonding strength by 50% to ensure simultaneous transmission of wear and eliminate the risk of tooth loss.
2.Structural optimization and self-sharpening design
- Wide shoulder taper + spin guide: evenly disperse the impact force, achieve 360° uniform wear, and fundamentally solve the problem of eccentric wear.
- Bionic self-sharpening mechanism: Based on the gradient structure of high wear resistance in the outer layer and high toughness in the inner layer, a sharp new edge is naturally formed during continuous wear, always maintaining the optimal cutting angle, and achieving the effect of “getting sharper with more use”.
Actual measurement results: synchronized wear and continuous sharpening are achieved, the material utilization rate exceeds 90%, and the service life of a single tooth reaches 2.8 times that of ordinary picks.
3. Efficiency is king: reshaping hard rock excavation standards

- Cost reduction: The service life is increased by more than 2 times, consumable costs are reduced by 60%, and equipment maintenance costs are reduced by 40%.
- Improved efficiency: downtime for gear replacement is reduced by 90%, footage per shift is increased from 3 meters to more than 4 meters, and monthly footage is increased by 30%.
- Strong stability: no risk of tooth chipping or handle breakage, small load fluctuation, safer operation.
In projects such as Shandong diversion tunnels and Guizhou hard rock coal mines, this pick has achieved “extremely low losses in a single shift and greatly improved efficiency”, completely solving the “stuck neck” problem in hard rock excavation.
4. Three suggestions for construction units
For 120MPa hard rock working conditions, we recommend:
- Pay attention to the scientific selection of picks: It is not advisable to pursue high hardness blindly, but to select pick models that match the rock formation conditions and can achieve “synchronous wear”.
- Grasp the changing patterns of wear: regularly record and analyze the wear data of the picks, construct a consumption trend curve suitable for this project, and dynamically adjust the excavation parameters accordingly.
- Evaluate the comprehensive cost of the whole cycle: The initial unit price of high-performance picks is relatively high, but if it can significantly reduce the frequency of gear replacement shutdowns and improve the excavation efficiency, it will often be more advantageous in terms of comprehensive benefits.
5. Conclusion

120MPa hard rock excavation is not about “hard loss”, but precise adaptation and intelligent efficiency improvement. Really high-efficiency picks, from synchronous wear to self-sharpening and crack suppression, make every excavation efficient and smooth. We will continue to innovate to help more projects overcome hard rock and achieve faster, cheaper and safer goals.